Reason Analysis of Single Stage Slurry Pump without Water

When we installed a single-stage slurry pump, during commissioning of equipment, if there is no water, how to deal with it? Today, Xiaobian to share this knowledge, I hope to give you some inspiration Find out why as soon as possible. Single-stage slurry pump causes no water (A) the air inlet pipe and the pump body: (1) before the start of the pump is not filled with enough water, and sometimes it seems that irrigation water has overflowed from the vent, but did not rotate the pump Shaft air fully discharged, resulting in a little residual air in the intake pipe or pump body. (2) The horizontal section of the inlet pipe in contact with the pump applies a descending gradient of 0.5% or more to the direction of the flow of water, and the one end connected to the inlet of the pump is the highest, not completely horizontal. If you tilt up, there will be trapped air inlet pipe, reducing the vacuum hose and pump, affecting water absorption. (3) The packing of the pump is worn or the packing pressure is too loose due to the long-term use, resulting in a large amount of water being ejected from the gap between the packing and the shaft sleeve of the pump. As a result, external air flows into the pump from these gaps, Affected the mention of water. (4) Inlet pipe Due to long-term potential underwater, pipe wall corrosion holes, water pumps continue to decline after work, when these holes exposed water, the air from the hole into the civilian into the water pipe. (5) cracks in the inlet pipe cracks, inlet pipe and pump connections appear tiny gaps, are likely to make the air into the inlet pipe. (B) pump speed is too low: (1) human factors. Some users due to the original motor damage, it is coupled with another motor driven, the result of a small flow, low lift or even the consequences of the water. (2) the pump itself mechanical failure. Loosening of the impeller and the shaft of the pump shaft or the deformation and bending of the shaft of the pump cause the impeller to move more, friction directly with the pump body or damage to the bearing, all of which may reduce the speed of the pump. (3) power machine repair is not working. Motor due to the winding burned, and lost magnetism, the maintenance of the winding turns, diameter, wiring changes, or maintenance failure is not completely ruled out the factors that will change the pump speed. (C) suction is too large: some deep water, some water outside the flat topography, while ignoring the pump allowable suction, resulting in less water absorption or simply can not absorb the results of the water. To know the pump suction port can establish a degree of vacuum is limited, the absolute vacuum suction is about 10 meters high water column, and the pump can not establish an absolute vacuum. And the vacuum is too large, easy to pump the water gasification, the work of the pump negative. Therefore, the centrifugal pump has its maximum allowable suction, usually between 3-8.5 meters. Do not install the pump only easy and simple. (D) of the flow of water out of the resistance loss is too large: Some users after the measurement, although the reservoir or water tower to the water surface of the vertical distance is slightly less than the pump head, but still mention the amount of water or mention the water. The reason is often too long pipes, pipe corners, water flow resistance in the pipeline is too large loss. The reason is often too long pipes, pipe corners, water flow resistance in the pipeline is too large loss. Under normal circumstances, 90-degree elbow bend than the 120-degree bend resistance, each 90-degree elbow head loss of about 0.5-1 meters, 20 meters of pipe resistance can make head loss of about 1 meter. In addition, some users are also free to pump into and out of the pipe diameter, which also has a certain impact on the lift. (E) the impact of other factors: (1) at the end of the valve can not be opened. It is usually due to the pump being left on for too long, the bottom valve gasket is stuck, and the bottom valve without gasket may rust. (2) The bottom valve filter screen is clogged; or the bottom valve causes potential clogging of the filter screen in the sludge layer. (3) impeller wear serious. Impeller blades worn by long-term use, affecting the pump performance. (4) Gate valve can check valve failure or blockage will result in reduced flow or even pumping on the water. (5) Leakage of the outlet pipe will also affect the amount of water lift. (Editor: Huang Nengwen QQ:)

Pvc Resin Series

Pvc Resin Series,Pvc Resin Prices,Pvc Resin Manufacturers,Pvc Resins

PVC resin serie,Lubricating agent series Co., Lt d , http://www.pvcseries.com